i Wasp 610/608 Barcode Printer User’s Manual
72.3 Operator Controls 2.3.1 Front Panel Display 2.3.2 LED Indicators LED Status Indication Off The printer power is turned off On
8 2.3.3 Front Panel Keys Keys Function 1. Enter the menu 2. Exit from a menu or cancel a setting and return to the previous menu Pause/Resume the
92.5 Installation of Ribbon 2.5.1 Loading Ribbon 1. Lift the right side printer cover to open it. 2. Push the print head release lever to open the p
10 5. Wrap the ribbon onto the ribbon rewind spindle, keeping the ribbon flat and without wrinkles. 6. Wind the ribbon clockwise about 3~5 rotations
11 Loading path for ribbon
122.5.2 Remove Used Ribbon 1. Cut the ribbon between ribbon guide plate and the ribbon rewind spindle. 2. Push the ribbon release button to release
132.6 Installation of Media 2.6.1 Loading Roll Labels 1. Lift open printer right side cover. 2. Push the print head release lever to open the print
14 5. Pull label roll leading edge forward through the media guide bar, damper, media sensor and place the label leading edge onto the platen roller.
15 7. Close the print head mechanism making sure the latches are engaged properly. 8. Using the front display panel, set the media sensor type and
162.6.2 Loading Fan-fold Labels Fan-fold media feeds through either the bottom or rear external label entrance chute. 1. Lift open printer right si
ii Contents 1. Introduction ... 1 1.1 Product Introduction...
17
182.6.3 Loading Media in Peel-off Mode (Option) 1. Lift open printer right side cover. 2. Push the print head release lever to open the print head m
19 12. Lift up the peel-off roller release lever and close the print head mechanism. 13. Rotate the peel-off sensor toward the paper exit chute.
202.6.4 Remove Liner from Internal Rewind 1. Cut the liner between peel-off roller and the internal rewind spindle. 2. Push the liner release but
212.6.5 Loading Media in Rewind Liner with Label Mode (Option) This mode can rewind the media including liner and label on the rewind spindle. 1. L
22 7. Using the LCD panel set the media sensor type and calibrate the selected sensor. (Please refer to section 3.1.2) Note: Please calibrate the g
232.6.6 Remove Labels from Internal Rewind (Option) 1. Slide off the labels with supply holder guides from the internal rewind spindle. Supply hol
242.7 Adjustment Knob 2.7.1 Print head Pressure Adjustment Knob The print head pressure adjustment knob has 5 levels of adjustment. Because the pri
25Caution: Incorrectly adjusting these knobs can lead to poor print quality and may cause damage to the printer. Proceed with caution. The print head
263. Menu Function Main Menu Overview RussianPolishSpanishExit↓↓↓Main MenuSetup File Manager Diagnostics Language Service Exit↓↓↓ ↓↓Printer Setup F
iii3.2.3 Del. All Files... 49 3.3 Diagnostics
273.1 Setup Menu Overview Exit↓Stop Bit(s)Exit↓Exit Data Bits↓↓↓ExitCalibration Parity Configure↓↓↓↓ZPL2Status Baud Rate Status↓↓↓SetupExitSensor Se
283.1.1 Printer Setup Printer SetupSpeed Density Direction Print Mode Offset Shift Y Reference X Code PageCountry+000~-000TSPL2↓Exit↓↓ ↓↓↓Shift X Ref
293.1.1.1 Speed: Use this option to setup print speed. The available print speed is between 4~12 ips and each increament/decreament is 1 ips. Th
30 DIRECTION 0 DIRECTION 1 Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite th
31command, which will overwrite the setting set from the front panel. 3.1.1.5 Offset: This option is used to fine tune media stop location. Pre
32REFERENCE command, which will overwrite the setting set from the front panel. 3.1.1.7 Code Page: Use this option to set the code page of inte
331258 Vietnam ISO Code Page ISO Code Page code page name International Character Set code page number International Character Set 8859-1 Latin
343.1.2 Sensor ExitStatus CalibrationSensor 3.1.2.1 Status This function is available to check the printer’s sensor status. When enter the [Status] o
35A. Gap Mode Press the and buttons to scroll the cursor to the media type and press the button to enter the sensor calibration mode. No
36 Gap Mode Scan Backing Intensity xRef. Level xxx3. Open the print head mechanism, put the label backing (liner) under the media s
1. Introduction 1.1 Product Introduction Congratulations on your purchase of a 610/608 barcode printer. This durable printer has a die-cast alumi
37 Paper Len. 00812 dot 1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0”
38B. Bline Mode Press the and buttons to scroll the cursor to the sensor type. Press the button to enter the black-mark sensor calibra
39 Bline Mode Scan Mark Intensity xRef. Level xxx3. Open the print head mechanism, put the black mark under the media sensor. Press
40 Paper Len. 00812 dot 1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0”
41C. Cont. Mode Press the and buttons to scroll the cursor to the sensor type. Press the button to enter the black-mark sensor calibra
42 Cont. Mode Complete Intensity xRef. Level xxx3. The sensor calibration is complete. Press the button the LCD screen will retur
433.1.3.1 Baud Rate Serial Comm. 1/5 > Baud Rate Parity Data Bits This option is used to set the RS-232 baud rate. The default setting i
443.1.3.4 Stop Bit(s): Serial Comm. 4/5 Parity Data Bits > Stop Bit(s) This option is used to set the RS-232 Stop Bits. The default sett
45 3.1.4 Ethernet Use this menu to configure internal Ethernet configuration check the printer’s Ethernet module status, and reset the Ethernet modul
463.1.4.1.2 MAC Ethernet 1/3 > Status Configure Exit The MAC address information will be shown on the LCD display. Please press o
2TÜV-GS: EN60950: 2000 Important Safety Warnings 1.Please read this reference manual carefully. 2.Keep these safety recommendations for later refer
47 3.1.4.2.2 Static IP Use this menu to set the printer's IP address, subnet mask and gateway. Ethernet 2/3 Status > Configure
483.2 File Manager This feature is used to check the printer available memory and file list. Exit Exit↓↓CARD CARD↓↓FLASH FLASH↓↓DRAM DRAMExit↓↓File
493.2.2 Avail. Memory Use this menu to show available memory space. File Manager 2/4 Avail. Memory File List DRAM: 256 KB
503.3 Diagnostics DiagnosticsExitPrint Config. Dump Mode Rotate Cutter 3.3.1 Print Config. This feature is used to print current printer configurati
513.3.2 Dump Mode Captures the data from the communications port and prints out the data received by printer. In the dump mode, all characters will b
523.3.3 Rotate Cutter In case paper is jammed in the cutter, this feature can rotate the cutter blade forward or backward, which is helpful to remov
533.5 Service ServiceInitialization Mileage Info. Exit This feature is used to restore all printer settings to their defaults and to display printer
54Bline sensor sensitivity 2 (Will be reset. Need to re-calibrate the gap) Language English IP address DHCP 3.5.2 Mileage Info. Use this option to
55 4. Troubleshooting 4.1 Common Problems The following guide lists the most common problems that may be encountered when operating this bar code p
56is not pin to pin connected. connected. - Check the baud rate setting. The default baud rate setting of printer is 9600,n,8,1. * If using the Ethe
32. Operations Overview 2.1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Carefully insp
57adjustment knob has been adjust to index “5” and the poor print quality is still at the left side of the printout, please adjust the pressure adjus
58 The left side printout position is incorrect * Wrong label size setup. * The parameter Shift X in LCD menu is incorrect. * Set the correct label s
594.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles This printer has been fully tested before delivery. There should be no ribbon wrinkle prese
60adjustment. 1. Decrease the right side print head pressure adjustment knob setting 1 level per each adjustment then print the label again to check
615. Maintenance This chapter provides information on the proper cleaning tools and methods to maintain your printer. 1. Please use one of follow
62 Please use 100% Ethanol. DO NOT use medical alcohol, which may damage the printer head. Regularly clean the print head and supply sensors whe
42.2 Printer Overview 2.2.1 Front View 1. LED indicators 2. LCD display 3. Front panel buttons 4. Paper exit chute 5. Lower front cover 6. Pri
52.2.2 Interior view 1. Ribbon rewind spindle 2. Ribbon release button 3. Ribbon guide plate 4. Print head 5. Platen roller 6. Print head rele
62.2.3 Rear View 1. Fan-fold paper entrance chute 2. Centronics interface 3. USB interface 4. RS-232C interface 5. Power jack socket 6. GPIO int
Commentaires sur ces manuels