Wasp WLS9500 Manuel d'utilisateur télécharger pdf (Page 51)

Keyboard Wedge Interface 5-5

Keyboard Wedge Host Parameters

Keyboard Wedge Host Types

Select the Keyboard Wedge host by scanning one of the bar codes below.

User selection is required to configure this interface and this is the most common selection.

IBM PC/AT & IBM PC Compatibles

IBM AT Notebook

NCR 7052

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 188 189

Wasp WLS 9500 1
WLS 9500 3
Product Reference Guide 3
Contents 5
Symbologies 7
Contents ix 9
About This Guide 11
Introduction 13
Notational Conventions 13
Service Information 13
Getting Started 15
Unpacking 17
Setting Up the Scanner 18
Scanning 19
Beeper Definitions 22
LED Definitions 22
Scanning in Hand-Held Mode 23
Scanning 2-7 25
Scanning in Hands-Free Mode 26
Scanning 2-9 27
Scanner Holder 27
Height Adjustment 27
Angle Adjustment 27
Decode Zone 28
Maintenance, Troubleshooting 29
Maintenance 31
Troubleshooting 31
Technical Specifications 34
User Preferences 37
Beeper Tone 42
Beeper Volume 42
*Medium Frequency 42
*High Volume 42
Power Mode 43
Scan Pattern 43
*Continuous On 43
*Multi-line Always Raster 43
Scan Line Width 44
Laser On Time 44
*Full Width 44
Beep After Good Decode 45
*Beep After Good Decode 45
Keyboard Wedge Interface 47
Keyboard Wedge Host Types 51
*North American 52
Ignore Unknown Characters 53
Keystroke Delay 54
Intra-Keystroke Delay 54
*No Delay 54
Convert Wedge Data 56
Function Key Mapping 56
*No Convert 56
*Disable Function Key Mapping 56
FN1 Substitution 57
Send Make and Break 57
Keyboard Maps 58
Keyboard Wedge Interface 5-21 67
7016 Dn Arrow 67
7017 Left Arrow 67
7018 Right Arrow 67
Extended Keypad Keystroke 67
USB Interface 69
Connecting a USB Interface 71
USB Parameter Defaults 72
USB Host Parameters 73
USB Keystroke Delay 76
USB CAPS Lock Override 76
USB Ignore Unknown Characters 77
Emulate Keypad 77
*Disable FN1 Substitution 78
Simulated Caps Lock 79
Convert Case 79
ASCII Character Set for USB 80
Symbologies 7-3 91
Symbology Parameter Defaults 94
Enable/Disable UPC-A/UPC-E 97
*Enable UPC-A 97
*Enable UPC-E 97
Enable/Disable UPC-E1 98
Enable/Disable EAN-13/EAN-8 98
*Disable UPC-E1 98
*Enable EAN-13 98
*Enable EAN-8 98
Enable/Disable Bookland EAN 99
*Disable Bookland EAN 99
*Ignore Supplementals 100
Transmit UPC-A Check Digit 101
*Transmit UPC-A Check Digit 101
Transmit UPC-E Check Digit 102
*Transmit UPC-E Check Digit 102
*System Character 103
Transmit UPC-E1 Check Digit 103
UPC-A Preamble 103
*Transmit UPC-E1 Check Digit 103
UPC-E Preamble 104
UPC-E1 Preamble 105
Convert UPC-E to UPC-A 105
Convert UPC-E1 to UPC-A 106
EAN-8/JAN-8 Extend 106
*Disable EAN/JAN Zero Extend 106
UCC Coupon Extended Code 107
Code 128 108
Enable/Disable ISBT 128 109
*Enable ISBT 128 109
Enable/Disable Code 39 110
*Enable Code 39 110
*Disable Trioptic Code 39 110
Convert Code 39 to Code 32 111
Code 32 Prefix 111
*Disable Code 32 Prefix 111
Set Lengths for Code 39 112
*Disable Code 39 Check Digit 113
Transmit Code 39 Check Digit 114
Code 39 Full ASCII Conversion 115
*Disable Code 39 Full ASCII 115
*Do Not Buffer Code 39 116
Clear Transmission Buffer 117
Transmit Buffer 117
Enable/Disable Code 93 119
Set Lengths for Code 93 119
*Disable Code 93 119
Code 93 - One Discrete Length 120
Code 93 - Length Within Range 120
Code 93 - Any Length 120
Set Lengths for Code 11 121
*Disable Code 11 121
Code 11 - One Discrete Length 122
Code 11 - Length Within Range 122
Code 11 - Any Length 122
Transmit Code 11 Check Digits 123
*Disable 123
Interleaved 2 of 5 (ITF) 124
Transmit I 2 of 5 Check Digit 126
Convert I 2 of 5 to EAN-13 126
Discrete 2 of 5 (DTF) 127
D 2 of 5 - Any Length 128
Chinese 2 of 5 129
Codabar (NW - 7) 130
CLSI Editing 131
*Disable CLSI Editing 131
NOTIS Editing 132
*Disable NOTIS Editing 132
Enable/Disable MSI 133
Set Lengths for MSI 133
*Disable MSI 133
MSI Check Digits 134
*One MSI Check Digit 134
Transmit MSI Check Digit(s) 135
MSI Check Digit Algorithm 135
*MOD 10/MOD 10 135
RSS (Reduced Space Symbology) 136
Convert RSS to UPC/EAN 137
Redundancy Level 138
Redundancy Level (continued) 139
Security Level 140
Bi-directional Redundancy 141
*Normal Intercharacter Gaps 142
Miscellaneous Scanner Options 143
Scanning Sequence Examples 145
Errors While Scanning 145
Transmit Code ID Character 147
Prefix/Suffix Values 147
Scan Data Transmission Format 148
*Data As Is 149
FN1 Substitution Values 150
Transmit “No Read” Message 150
*Set FN1 Substitution Value 150
*Disable No Read 150
Standard Default Parameters 153
Sample Bar Codes 159
UPC-A, 100% 161
EAN-13, 100% 161
123456789012 162
Numeric Bar Codes 165
ASCII Character Sets 169
Table D-4. GUI Shift Keys 175
Programming Reference 181
Symbol Code Identifiers 183
AIM Code Identifiers 184
]C1AIMID 185

Commentaires sur ces manuels

Pas de commentaire

Wasp WLS9500 Manuel d'utilisateur Page 51

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimer et scanner Wasp WLS9500